NEWS CENTER

News Center

Get the latest news about Konger, including new product launches, industry exhibitions, technical updates and market trends of the injection molding industry.

11·22 Choosing a Fruit Crate Dedicated Injection Molding Machine: From Part Features to Machine Configuration | Konger

Choosing a Fruit Crate Dedicated Injection Molding Machine: From Part Features to Machine Configuration | Konger

A crate is thin-walled, deep and large in projected area, and has to carry a stacked load. Four part features, the difference a dedicated machine makes, four selection traps and a trial checklist.

Industry News · 2026-11-22
11·20 Interface Commissioning on Horizontal Injection Molding Machines: Mould, Auxiliary and Automation Coordination | Konger

Interface Commissioning on Horizontal Injection Molding Machines: Mould, Auxiliary and Automation Coordination | Konger

The last mile of commissioning is rarely on the machine itself. Six interface problems between injection molding machines, moulds, auxiliary equipment and automation, with the order and checklist to commission them.

Industry News · 2026-11-20
11·16 Ten "False Faults" in Horizontal Injection Molding Machine Commissioning | Konger

Ten "False Faults" in Horizontal Injection Molding Machine Commissioning | Konger

Most commissioning time is lost to false faults rather than real ones. Ten common misjudgements on horizontal injection molding machines, the evidence that separates them from genuine faults, and what to do about each.

Industry News · 2026-11-16
11·15 Commissioning Troubleshooting for Horizontal Injection Molding Machines: Eight Common Issues | Konger

Commissioning Troubleshooting for Horizontal Injection Molding Machines: Eight Common Issues | Konger

Most commissioning problems are not process problems. A practical path through eight common issues on horizontal injection molding machines: no clamp, weak clamping force, injection unit judder, nozzle leaks, short shot with flash, weight drift, ejection faults and mold-protection false alarms, with Konger K-TEC design and service support.

Industry News · 2026-11-15
11·15 Nozzle Alignment on Horizontal Injection Molding Machines | Konger

Nozzle Alignment on Horizontal Injection Molding Machines | Konger

An off-centre nozzle leaks at the sprue bush, destabilises the cushion and wears the bush on one side. A step-by-step method: locating-ring datum, dial-indicator and imprint checks, lateral, height and pitch adjustment, re-check after tightening, and hot-state verification.

Industry News · 2026-11-15
11·14 Clamping Force Calibration & Low-Pressure Mold Protection | Konger

Clamping Force Calibration & Low-Pressure Mold Protection | Konger

Clamping force is not a matter of more is better. A field guide to projected-area and specific-pressure estimation, on-machine force calibration, stepped low-pressure mold protection and template parallelism checks, with Konger K-TEC clamping design.

Industry News · 2026-11-14
11·14 Horizontal injection molding machine installation and commissioning full process guide: Konger model technical advantages analysis

Horizontal injection molding machine installation and commissioning full process guide: Konger model technical advantages analysis

Complete technical path for horizontal injection molding machine installation and commissioning: from foundation load-bearing, rough and fine leveling, and template parallelism, to hydraulic exhaust, segmented temperature curves, clamping force estimation, and low-pressure protection setting, to short shot method first mold verification. Combining the advantages of Konger K-TEC, CMS series in clamping rigidity, precision temperature control, and specialized configuration, and including common commissioning fault troubleshooting directions, to help on-site shorten machine setup cycles.

Industry News · 2026-11-14
11·08 Ningbo Konger K-TEC1200 Injection Machine Installation Chronicle|Split Three-Plate Model, Safe Hoisting and Placement

Ningbo Konger K-TEC1200 Injection Machine Installation Chronicle|Split Three-Plate Model, Safe Hoisting and Placement

Konger K-TEC1200 large horizontal three-plate injection molding machine installation site record, the site strictly follows lifting safety regulations, with division of labor and coordinated, orderly operations, ensuring stable lifting and precise alignment of the equipment, laying a foundation for subsequent equipment commissioning and production operation. Konger provides one-stop service for complete machine delivery, on-site installation, and technical guidance, assisting customers in establishing their large-scale injection molding production line.

Video Center · 2026-11-08
11·05 Ningbo Konger K-TEC Series Injection Molding Machines Delivery Update: K-TEC170,360,500,650,800 Shipped by 3 Trailers Today, K-TEC1200 Large Injection Machine to Ship Tomorrow

Ningbo Konger K-TEC Series Injection Molding Machines Delivery Update: K-TEC170,360,500,650,800 Shipped by 3 Trailers Today, K-TEC1200 Large Injection Machine to Ship Tomorrow

Shipment update from Ningbo Konger Machinery. Three trailers are fully loaded with our K-TEC series servo injection molding machines: K-TEC170, K-T。

Video Center · 2026-11-05
10·30 Troubleshooting and Solutions for the Fault: The Material Storage Solenoid Valve Indicator Light of Horizontal Injection Molding Machine Is On, but the Screw Does Not Store Material

Troubleshooting and Solutions for the Fault: The Material Storage Solenoid Valve Indicator Light of Horizontal Injection Molding Machine Is On, but the Screw Does Not Store Material

In after-sales maintenance of horizontal injection molding machines, a typical fault is frequently encountered: when the material charging (melting) action is triggered, the indicator light of the material charging (plasticizing) solenoid valve lights up normally and the PLC output signal is valid, yet the screw fails to rotate and no charging back-off action occurs. A lit indicator only means the solenoid coil receives an electrical signal; it does not guarantee the hydraulic circuit has shifted properly or built up driving pressure. Following the troubleshooting principle of **from simple to complex, external checks before internal disassembly**, this article sorts out all potential fault causes, judgment methods and corresponding solutions to help on-site technicians and workshop maintenance personnel locate faults quickly and carry out maintenance safely.

Industry News · 2026-10-30