At commissioning, most of the lost time does not go into real faults. It goes into false ones: a venting problem read as low injection pressure, damp material read as a temperature-control fault, a lost ejector return signal read as a damaged clamping valve. Drawing on Konger's experience at machine installation and after-sales support, this article lists ten common misjudgements, the evidence that separates them from genuine faults, and what to do about each.
1. Where misjudgements come from
An observation window that is too short
Three to five shots are not a result. On a fresh mould the mould temperature has not stabilised and the barrel has not reached thermal equilibrium, so the first few dozen shots do not represent steady state.
Variables that were never separated
Changing the mould, the material and the process settings at the same time makes it impossible to say which one caused the change. Move one variable at a time.
No baseline
Without recorded hydraulic pressure, clamp force readings, zone temperatures and cooling-water temperature there is no reference against which "something is wrong" can be judged. The baseline is a precondition, not paperwork.
2. Ten common misjudgements
2.1 "Not enough injection pressure" — actually venting or gate size
The symptom is short fill at the end of flow with burnt edges. Check whether the vent is blocked by oil or residue, and whether the gate matches the wall thickness, before adding pressure. Adding pressure blindly brings flash and residual stress along with it.
2.2 "Insufficient clamp force" — actually mould height or protection setting
Excess mould height puts the clamp force into the toggle mechanism, and a mould-protection threshold set too tight stops the platen before it reaches position. Re-check mould height and protection settings, then confirm clamp force against projected area, and only then suspect the clamping unit.
2.3 "The temperature control is off" — actually thermocouple or thermal equilibrium
A thermocouple seated too shallow, or a heater band not in proper contact with the barrel, makes the displayed value drift from the real melt temperature. Allow 20–30 minutes at set temperature before judging.
2.4 "Nozzle leakage is a machine fault" — actually contact and settings
A nozzle that is not concentric with the sprue bush, nozzle temperature set too high, insufficient suck-back, or a worn check ring all cause drooling. Verify alignment hot first, then correct nozzle temperature and suck-back, and inspect the check ring last.
2.5 "Injection unit judder is a hydraulic failure" — actually guideway and settings
Dry or contaminated guideways, unsuitable back pressure or speed settings, and servo valve zero drift all produce low-speed judder. Clean and lubricate the guideway, run slow reciprocation without load to purge air, then evaluate the valve.
2.6 "Sink marks mean low hold pressure" — actually gate freeze and cushion
If the gate freezes early, hold pressure never reaches the cavity. If the cushion is unstable, the amount of material available for compensation differs from shot to shot. Read the cushion curve and gate freeze time before touching hold pressure.
2.7 "Weld lines mean low melt temperature" — actually flow ratio and venting
The strength at a weld line depends on the temperature and pressure at which the two flow fronts meet, and on whether air can escape from that point. Adjusting flow ratio, venting and gate position usually does more than raising temperature.
2.8 "Dimension drift means poor machine accuracy" — actually cooling and environment
Variation in cooling-water temperature, shop temperature and material moisture all shift shrinkage. Stabilise the temperature controller and the cooling circuit first, then compare dimensions.
2.9 "An alarm means a broken component" — actually signal sequence
An ejector that has not fully returned, a loose safety-gate limit switch, or a displaced proximity switch will all trigger alarms that look like hardware failures. Confirm whether the signal condition behind the alarm is actually satisfied before removing parts.
2.10 "The machine cannot handle the new material" — actually material differences
Flowability, shrinkage and masterbatch ratio can differ between batches, and hygroscopic material that was not dried properly shows silver streaks. Re-establish the process window after a material change before judging the machine.
3. Turning a suspicion into a conclusion
Build a baseline first
Record hydraulic pressure, clamp force, zone temperatures, cooling-water temperature and the cushion curve. Every later "abnormality" is judged against this line.
Change one variable
Alter one setting at a time and observe at least ten shots before reading the trend instead of a single shot.
Reproduce three times
A phenomenon that reproduces across three independent adjustments is a systematic problem; one that appears once is usually interference.
4. How Ningbo Konger supports this work
Ningbo Konger Machinery Co., Ltd. is based in Ningbo, founded in 2013, and covers the development, manufacture, sales and service of injection molding machines. The range is built around the K-TEC servo energy-saving series, with CMS (Color Mixing System) two-colour and sandwich machines, plus dedicated configurations for PET preforms, artificial flowers, TPR soft compounds and flame-retardant nylon — close to thirty customised models in total.
For commissioning, those design choices mean something concrete:
A stable datum. K-TEC uses a split three-platen structure with thickened platens, so clamp force travels a short path and long-term deformation stays small — fewer cases of "it was right yesterday and drifted today".
Controllable pressure and temperature. The servo hydraulic system supplies oil on demand with a closed-loop pressure response, and the barrel uses zone-by-zone PID control, which removes the impression that settings "will not move".
Matched dedicated models. Screw, nozzle and temperature configuration follow the material, so the process window after a material change starts closer to target and material differences are less likely to be read as machine faults.
Reusable parameters. Process and mould parameters can be stored and recalled, so after a mould change the historical values can be compared to tell a machine change from a mould change.
5. On-site checklist
Did the problem exist before the mould change?
Did it exist before the material change?
What were the baseline pressure, temperature and clamp force?
Does the symptom follow a single changed variable?
Does it reproduce three times?
Have venting, gate and water circuits been cleaned?
Has the material been dried as the process requires?
Is the signal condition behind the alarm actually satisfied?
Conclusion
Judgement at commissioning comes from three habits: a baseline, one variable at a time, and reproduction. Clearing the false faults first, then discussing machine and process, saves a great deal of trial-and-error. Konger's work on structural rigidity, closed-loop pressure and dedicated model configuration is, in essence, about making those misjudgements less likely.